BYR Achieve · 镜像论坛

☆─────────────────────────────────────☆ DA (DA229 ) 于 (Mon Jun 2 20:18:31 2008) 提到: ☆─────────────────────────────────────☆ tjfmail (PE_passion & energy) 于 (Tue Jun 3 14:36:14 2008) 提到: 正在分析u-boot源码的路过初学者路过 ☆─────────────────────────────────────☆ lester98 (奶瓶) 于 (Wed Jun 4 17:28:55 2008) 提到: 在cpu/xxx/start.s里 /* * void relocate_code (addr_sp, gd, addr_moni) * * This "function" does not return, instead it continues in RAM * after relocating the monitor code. * * r3 = dest * r4 = src * r5 = length in bytes * r6 = cachelinesize */ .globl relocate_code relocate_code: mr r1, r3 /* Set new stack pointer */ mr r9, r4 /* Save copy of Init Data pointer */ mr r10, r5 /* Save copy of Destination Address */ mr r3, r5 /* Destination Address */ lis r4, CFG_MONITOR_BASE@h /* Source Address */ ori r4, r4, CFG_MONITOR_BASE@l lwz r5, GOT(__init_end) sub r5, r5, r4 li r6, CFG_CACHELINE_SIZE /* Cache Line Size */ /* * Fix GOT pointer: * * New GOT-PTR = (old GOT-PTR - CFG_MONITOR_BASE) + Destination Address * * Offset: */ sub r15, r10, r4 /* First our own GOT */ add r14, r14, r15 /* the the one used by the C code */ add r30, r30, r15 /* * Now relocate code */ cmplw cr1,r3,r4 addi r0,r5,3 srwi. r0,r0,2 beq cr1,4f /* In place copy is not necessary */ beq 7f /* Protect against 0 count */ mtctr r0 bge cr1,2f la r8,-4(r4) la r7,-4(r3) 1: lwzu r0,4(r8) stwu r0,4(r7) bdnz 1b b 4f 2: slwi r0,r0,2 add r8,r4,r0 add r7,r3,r0 3: lwzu r0,-4(r8) stwu r0,-4(r7) bdnz 3b /* * Now flush the cache: note that we must start from a cache aligned * address. Otherwise we might miss one cache line. */ 4: cmpwi r6,0 add r5,r3,r5 beq 7f /* Always flush prefetch queue in any case */ subi r0,r6,1 andc r3,r3,r0 mr r4,r3 5: dcbst 0,r4 add r4,r4,r6 cmplw r4,r5 blt 5b sync /* Wait for all dcbst to complete on bus */ mr r4,r3 6: icbi 0,r4 add r4,r4,r6 cmplw r4,r5 blt 6b 7: sync /* Wait for all icbi to complete on bus */ isync /* * We are done. Do not return, instead branch to second part of board * initialization, now running from RAM. */ addi r0, r10, in_ram - _start + EXC_OFF_SYS_RESET mtlr r0 blr /* NEVER RETURNS! */ in_ram: /* * Relocation Function, r14 point to got2+0x8000 * * Adjust got2 pointers, no need to check for 0, this code * already puts a few entries in the table. */ li r0,__got2_entries@sectoff@l la r3,GOT(_GOT2_TABLE_) lwz r11,GOT(_GOT2_TABLE_) mtctr r0 sub r11,r3,r11 addi r3,r3,-4 1: lwzu r0,4(r3) add r0,r0,r11 stw r0,0(r3) bdnz 1b /* * Now adjust the fixups and the pointers to the fixups * in case we need to move ourselves again. */ 2: li r0,__fixup_entries@sectoff@l lwz r3,GOT(_FIXUP_TABLE_) cmpwi r0,0 mtctr r0 addi r3,r3,-4 beq 4f 3: lwzu r4,4(r3) lwzux r0,r4,r11 add r0,r0,r11 stw r10,0(r3) stw r0,0(r4) bdnz 3b 4: clear_bss: /* * Now clear BSS segment */ lwz r3,GOT(__bss_start) lwz r4,GOT(_end) cmplw 0, r3, r4 beq 6f li r0, 0 5: stw r0, 0(r3) addi r3, r3, 4 cmplw 0, r3, r4 bne 5b 6: mr r3, r9 /* Init Data pointer */ mr r4, r10 /* Destination Address */ bl board_init_r /* * Copy exception vector code to low memory * * r3: dest_addr * r7: source address, r8: end address, r9: target address */ .globl trap_init trap_init: lwz r7, GOT(_start) lwz r8, GOT(_end_of_vectors) li r9, 0x100 /* reset vector always at 0x100 */ cmplw 0, r7, r8 bgelr /* return if r7>=r8 - just in case */ mflr r4 /* save link register */ 1: lwz r0, 0(r7) stw r0, 0(r9) addi r7, r7, 4 addi r9, r9, 4 cmplw 0, r7, r8 bne 1b /* * relocate `hdlr' and `int_return' entries */ li r7, .L_MachineCheck - _start + EXC_OFF_SYS_RESET li r8, Alignment - _start + EXC_OFF_SYS_RESET 2: bl trap_reloc addi r7, r7, 0x100 /* next exception vector */ cmplw 0, r7, r8 blt 2b li r7, .L_Alignment - _start + EXC_OFF_SYS_RESET bl trap_reloc li r7, .L_ProgramCheck - _start + EXC_OFF_SYS_RESET bl trap_reloc li r7, .L_FPUnavailable - _start + EXC_OFF_SYS_RESET li r8, SystemCall - _start + EXC_OFF_SYS_RESET 3: bl trap_reloc addi r7, r7, 0x100 /* next exception vector */ cmplw 0, r7, r8 blt 3b li r7, .L_SingleStep - _start + EXC_OFF_SYS_RESET li r8, _end_of_vectors - _start + EXC_OFF_SYS_RESET 4: bl trap_reloc addi r7, r7, 0x100 /* next exception vector */ cmplw 0, r7, r8 blt 4b mtlr r4 /* restore link register */ blr /* * Function: relocate entries for one exception vector */ trap_reloc: lwz r0, 0(r7) /* hdlr ... */ add r0, r0, r3 /* ... += dest_addr */ stw r0, 0(r7) lwz r0, 4(r7) /* int_return ... */ add r0, r0, r3 /* ... += dest_addr */ stw r0, 4(r7) blr

[合集] 有人了解u-boot中的relocate_code函数吗？